top of page
CVC Engineers Pte Ltd

Geotechnical Engineering in Singapore: The Complete Guide to Soil Foundations Excavations Slopes and Tunnels

7 days ago
11 min read

Geotechnical engineering is the branch of civil engineering that deals with how soil, rock and groundwater behave, and with the structures that are built on, in and out of the ground. A geotechnical engineer investigates the ground, predicts how it will respond to loading and excavation, and designs the foundations, retaining structures, slopes and tunnels that depend on it. It matters more in Singapore than in most cities because the island builds deep basements and MRT tunnels through soft marine clay and reclaimed land, beside existing buildings, under tropical rainfall that tests every slope.

What Do Geotechnical Engineers Do?

Geotechnical engineers work in ten connected areas.

  • Soil and rock mechanics: The study of how soil and rock carry load, deform and let water through. It supplies the shear strength, stiffness, compressibility and permeability parameters used in every later design step.

  • Site investigation: The planned exploration of the ground before design, through a desk study, boreholes, in-situ tests such as the standard penetration test (SPT), geophysical surveys and laboratory testing. In Singapore the results go into a site investigation report certified by a Professional Engineer and submitted to BCA.

  • Foundation design: The design of the elements that transfer building loads into the ground, including pad and strip footings, raft foundations, bored piles, driven piles, micropiles, barrettes and caissons. The engineer selects the foundation type and checks both its load capacity and its settlement.

  • Excavations and earth retaining structures: The design of the walls and supports that hold the ground back while a basement, pit or trench is dug, known in Singapore as earth retaining or stabilising structures (ERSS). Typical elements are sheet piles, soldier piles, contiguous bored piles, secant bored piles, diaphragm walls, struts, walers and ground anchors.

  • Tunnels and shafts: The design of bored, mined, jacked and cut-and-cover tunnels and their shafts, covering both temporary support and permanent lining. MRT tunnels, sewer and cable tunnels and pipe jacking for utilities all belong here.

  • Slopes and earthworks: The assessment and stabilisation of natural slopes, cut slopes, embankments and fill, using regrading, drainage, soil nails, ground anchors and retaining walls. In Singapore the governing concern is slope failure triggered by rainfall.

  • Ground improvement: Techniques that change the ground itself so that it becomes stronger, stiffer or less permeable, such as jet grouting, deep soil mixing, prefabricated vertical drains with surcharge, and vibro methods.

  • Land reclamation: The creation of new land by placing fill over the seabed, together with the prediction and acceleration of the settlement that follows as the soft clay beneath the fill consolidates.

  • Instrumentation and monitoring: The measurement of ground and structural behaviour during construction with inclinometers, settlement markers, piezometers, water standpipes, strain gauges and tiltmeters. Readings are compared with predicted values and with pre-set alert and work suspension levels.

  • Impact assessment and protection of neighbouring structures: The prediction of how far an excavation or tunnel will move the ground beneath adjacent buildings, roads, utilities and rail tunnels, and the design of measures that keep damage within accepted limits. It is paired with pre-construction surveys of neighbouring properties.

Soil and Rock Mechanics

Soil and rock mechanics is the science that explains how the ground carries load, changes shape and conducts water.

The central idea is effective stress: soil strength depends on the stress carried by its grains, which is the total stress less the pore water pressure. Design in Singapore follows Eurocode 7. Read more in soil and rock mechanics basics and how SS EN 1997 governs geotechnical design.

Site Investigation

Site investigation is the exploration of the ground by desk study, drilling, in-situ testing, geophysics and laboratory testing. In Singapore it is a legal duty: Regulation 31 of the Building Control Regulations 2003 requires the qualified person for structural works to carry out proper and adequate site investigation where foundations, tunnels, excavations or related earthworks are proposed.

The current reporting standard is BCA's Guideline on Requirements for Site Investigation Reports (APPBCA-2025-16, 1 September 2025), which applies to new projects submitted to URA for planning permission on or after 1 March 2026 and to reports dated on or after that day. The report must be a standalone PDF with an AGS(SG) data file, certified by an appropriate Professional Engineer, with strata named under the new stratigraphical framework and a calibration certificate for each SPT hammer. BCA's 2026 submission requirements add that the fieldwork must be done by a firm accredited by the Singapore Accreditation Council. Details are in soil investigation in Singapore.

Foundation Design

Foundation design is the selection and sizing of the footings, rafts or piles that carry a structure's load into the ground without bearing failure or excessive settlement. Shallow foundations spread load near the surface; deep foundations carry it down to stronger soil or rock.

Under BCA's June 2026 submission requirements, the foundations of buildings of 30 or more storeys are geotechnical building works, with raft, caisson, barrette and piled raft foundations given as examples. Those projects need a PE(Geo) and an AC(Geo). See foundation design and pile types, pile load tests and integrity tests and our foundation design review service.

Excavations and Earth Retaining Structures (ERSS)

An earth retaining structure is, in BCA's definition, any structure, structural system or other means used to maintain the shape of an excavation during construction, earth filling or cutting. Who must design and check it depends on depth.

BCA's ERSS submission requirements (August 2026 edition) set these bands:

  • Up to 1.5 m deep (1 m if the retaining structure is not reinforced concrete or steel): plan approval is not required.

  • More than 1.5 m and up to 4 m: a qualified person for structural works submits; no Accredited Checker.

  • More than 4 m and up to 6 m: qualified person plus Accredited Checker.

  • More than 6 m and classed as geotechnical building works, such as a basement excavation: qualified person, PE(Geo), Accredited Checker and AC(Geo).

  • Localised pits for a pile cap, footing, sump, lift pit or trench need no submission if they do not exceed 10 sqm in area and 2 m in depth.

BCA Advisory Note 1/09 controls movement. It states that the allowable maximum wall deflection should not exceed 0.5% of the excavation depth H where existing structures lie within a distance H of the excavation, and 0.7% of H where they lie between H and 2H. Read ERSS submission thresholds and ERSS explained, then ERSS wall types, deep excavation and AC(Geo) requirements, top-down and bottom-up basement construction, groundwater control and dewatering and the observational method. See also our ERSS submission service.

Tunnels and Shafts

Tunnelling becomes geotechnical building works in Singapore when the tunnel is more than 2 m in diameter, width or height. For bored and jacked tunnels both the permanent lining and the temporary support are covered.

On 19 October 2026 BCA, ACES, IES and GeoSS issued risk-based guidelines on ERSS shafts for utility works (APPBCA-2026-23), which rate each shaft Low, Medium or High risk by ground type and distance to buildings. See tunnelling, pipe jacking and shafts, PE geotechnical and tunnel endorsement explained and our geotechnical and tunnel endorsement service.

Slopes and Earthworks

Slope engineering is the assessment of whether a natural or cut slope will stay stable, and the design of drainage, reinforcement or retaining structures where it will not. BCA states that rainfall-induced failure is the most common form of slope failure in Singapore, usually during heavy or prolonged rain.

BCA's Framework on Risk-Based Slope Designs (APPBCA-2024-01, 2 January 2024) classes an engineered slope as High, Medium or Low impact according to the buildings inside its potential failure zone, taken as 0.7H from the crest or 1H from the toe. A High impact slope needs at least two boreholes per design section. Slopes higher than 6 m are geotechnical building works, and alterations that materially affect an existing slope need an Accredited Checker above 4 m. See slope stability and the risk-based framework and retaining walls and slopes for landed houses.

Ground Improvement

Ground improvement is any technique that changes the properties of the ground in place, such as jet grouting, deep soil mixing, vertical drains with preloading, or vibro compaction.

BCA's June 2026 requirements limit how it may be relied on: ground improvement is to be soil improvement only and must not be used as part of the retaining wall, especially as a cantilever wall. Where grout mixed piles sit within a wall, a separate structural system must resist all wall forces. See ground improvement methods.

Land Reclamation and Soft Ground

Land reclamation is the formation of new land by placing fill in the sea, and its main engineering problem is consolidation: soft clay under the fill squeezes out water and settles over years. Engineers predict that settlement and shorten it with vertical drains and surcharge.

BCA's 2025 sheet pile circular and 2026 shaft guidelines both name reclaimed sand and highly permeable soils as conditions behind recent ground loss incidents. See marine clay, settlement and land reclamation.

Instrumentation and Monitoring

Instrumentation and monitoring is the measurement of wall deflection, ground settlement, groundwater level and strut load during construction, so that real behaviour can be checked against the design and against defined trigger levels.

Under Advisory Note 1/09 the work suspension level is the allowable wall deflection limit, with an alert level at 70% of it, and the qualified person sends monitoring results to BCA by the 7th of each month. See instrumentation and monitoring for excavation works and our structural monitoring service.

Impact Assessment and Protection of Neighbouring Structures

An impact assessment predicts the ground movement caused by an excavation or tunnel and the damage it could do to adjacent buildings and infrastructure. In Singapore it is governed by BCA's Framework on Performance Based Impact Assessment, reissued on 6 March 2024.

The Deemed-to-Satisfy Approach applies to all projects and requires the qualified person to show that the predicted building damage category is no worse than Very Slight. The Rigorous Approach is open only to geotechnical building works and brings enhanced monitoring, including settlement of every external column. See impact assessment and pre-construction surveys and building near MRT lines.

Singapore Ground Conditions in Brief

Singapore's ground ranges from very soft recent deposits to strong rock, often within one site. The official reference is the 1:50,000 Singapore Geological Map and Memoir published by BCA in 2021 (circular APPBCA-2021-18, 1 October 2021), which renamed the units used since the 2009 edition.

  • Kallang Group: the recent deposits that include soft marine clay and fluvial sand. BCA's 2025 and 2026 circulars treat it as the higher-risk ground for sheet piles and shafts.

  • Old Alluvium, now named the Bedok Formation.

  • Jurong Formation, now raised to the Jurong Group, with the younger Sentosa Group defined separately.

  • Bukit Timah Granite: the granite found mostly in central and northern Singapore.

Who Regulates Geotechnical Work in Singapore?

BCA is the main regulator, under the Building Control Act 1989 and the Building Control Regulations 2003.

  • BCA approves plans and issues the permit for ERSS and geotechnical building works. Geotechnical building works are tunnels of more than 2 m, excavations, earth retaining structures and slopes of more than 6 m, and foundations for buildings of 30 or more storeys. ERSS bands sit at 1.5 m, 4 m and 6 m.

  • The Professional Engineers Board (PEB) registers the PE(Geo). Under its April 2026 guidelines the applicant must be a PE in civil engineering with four years of geotechnical experience plus a postgraduate degree in the field, or five years plus a pass in the specialist examination.

  • LTA protects the rail network. The railway protection zone is 40 m from the railway, the railway safety zone is 60 m and the first reserve is 6 m.

  • PUB, the national water agency, is involved where works affect public sewers, drains and water mains.

  • URA grants planning permission, which comes before the BCA submissions.

What Changed Recently (2024 to 2026)

Ten updates issued since January 2024 define current geotechnical practice in Singapore.

  • 2 January 2024: BCA Framework on Risk-Based Slope Designs (APPBCA-2024-01). Slope impact categories now set the borehole, groundwater, subsoil drain and long-term monitoring requirements.

  • 6 March 2024: BCA Framework on Performance Based Impact Assessment for ERSS and tunnelling works.

  • 1 September 2025: Guideline on Requirements for Site Investigation Reports (APPBCA-2025-16), effective 1 March 2026.

  • 1 December 2025: Joint BCA, ACES, IES and GeoSS guideline on the integrity of sheet pile walls (APPBCA-2025-29). For geotechnical building works deeper than 6 m, the approved plans must specify inspection of the exposed interlocks and contingency measures if a gap is found.

  • June and August 2026: BCA reissued its submission requirements for geotechnical building works (June) and ERSS (August). Thresholds are unchanged; the August edition adds an accidental basal heave check, to a factor of safety of not less than 1.1, for ERSS that uses ground improvement with the wall toe in soft soil.

  • 23 July 2026: BCA and URA circular APPBCA-2026-12. CORENET X is mandatory for new projects of 30,000 sqm gross floor area and above since 1 October 2025 and of 5,000 sqm and above from 1 October 2026; smaller projects can continue on CORENET 2.0 for now.

  • 1 September 2026: LTA circular and addendum to the Code of Practice for Railway Protection, 2024 edition. Works affecting bored tunnels in compressible soils need a consolidation analysis and must minimise added load and groundwater drawdown. The header gives an effective date of 1 March 2027 while the body says the enhancements take effect from 1 September 2026, so confirm the date with LTA.

  • 23 September 2026: BCA enhancements to the Accredited Checker system (APPBCA-2026-20), adding experience and performance conditions for checkers of higher-value projects.

  • 9 October 2026: Joint BCA and LTA circular on diaphragm wall quality (APPBCA-2026-22), recommending tremie concrete with a slump flow of 400 mm to 550 mm, a 0.30 mm design crack width, 75 mm minimum cover and at most three layers of reinforcement.

  • 19 October 2026: Risk-based guidelines on ERSS shafts for utility works (APPBCA-2026-23). A physical retaining wall installed before excavation is the default for shafts within 1H of a building, to a maximum of 10 m.

When Do You Need a Geotechnical Engineer?

You need geotechnical input whenever the ground controls the risk. By project type:

  • Landed house basement or retaining wall: any excavation or retaining structure deeper than 1.5 m needs a plan submission by a qualified person, an Accredited Checker above 4 m and a PE(Geo) above 6 m.

  • Factory extension with piling: site investigation is mandatory, and pile type and capacity are geotechnical questions even where no PE(Geo) is required.

  • Deep basement: once the excavation exceeds 6 m, a PE(Geo) and an AC(Geo) must be appointed.

  • Works near MRT: restricted activities within the 40 m railway protection zone need LTA clearance.

  • Slope behind a property: works that affect an existing slope higher than 4 m need a qualified person and an Accredited Checker, and a PE(Geo) above 6 m.

  • Reclaimed or soft ground: resolve settlement, sheet pile integrity and groundwater control before the structure is designed.

FAQ

What is geotechnical engineering?

It is the branch of civil engineering concerned with the behaviour of soil, rock and groundwater and with the design of foundations, excavations, retaining structures, slopes and tunnels.

What is the difference between a geotechnical engineer and a structural engineer?

A structural engineer designs the building frame; a geotechnical engineer designs for the ground that supports or surrounds it. In Singapore a PE(Geo) is a civil professional engineer with an additional specialist registration from PEB.

What is a PE(Geo)?

A PE(Geo) is a professional engineer registered under the Professional Engineers Act as a specialist professional engineer in geotechnical engineering.

When is a soil investigation required in Singapore?

Whenever foundations, tunnels, excavations or related earthworks are proposed, under Regulation 31 of the Building Control Regulations 2003.

What are geotechnical building works?

They are tunnels of more than 2 m in diameter, width or height; excavations, earth retaining structures and slopes of more than 6 m; and foundations for buildings of 30 or more storeys.

How deep can I excavate without BCA approval?

Up to 1.5 m generally, or 1 m if the retaining structure is not reinforced concrete or steel. A localised pit for a footing, pile cap, sump, lift pit or trench may go to 2 m if its area does not exceed 10 sqm.

Who checks a geotechnical design?

An Accredited Checker checks ERSS deeper than 4 m, and an AC(Geo) also checks the geotechnical aspects of geotechnical building works.

Sources

CVC Engineers advocates education and public awareness, and has a dedicated team to help resolve this properly. WhatsApp +65 9342 7551. Last reviewed: November 2026.

Recent Posts

See All

Comments


© 2024 CVC Engineers. All rights reserved.

bottom of page