top of page
CVC Engineers Pte Ltd

Singapore Geology for Engineers: Kallang Formation Old Alluvium Jurong Formation and Bukit Timah Granite

Nov 12
8 min read

Singapore's ground is made up of four main families that engineers have long called the Kallang Formation (soft marine clay and other recent deposits), the Old Alluvium (dense, variably cemented sand and clay), the Jurong Formation (folded sedimentary rocks, including limestone) and the Bukit Timah Granite with its thick residual soil. Since BCA released a new geological map and memoir in 2021, each of these has an official new name, and BCA circular APPBCA-2022-02 requires the new unit names in borehole logs and AGS(SG) data for all site investigation works carried out from 1 October 2022. This guide gives both sets of names and explains what each unit means for foundations and excavations. It is one part of our complete guide to geotechnical engineering in Singapore.

What are the main geological units in Singapore?

The main units an engineer meets are the Kallang Formation, the Old Alluvium, the Fort Canning Boulder Bed, the Jurong Formation and the Bukit Timah Granite, plus man-made fill and reclaimed land on top. The Land Transport Authority's Civil Design Criteria (Revision A2, September 2019) classifies Singapore's common soils and rocks by these geological origins:

  • Kallang Formation: beach (littoral) sands, estuarine peats and organic clays, fluvial sands and clays, and marine clay described as very soft to soft blue or grey clay.

  • Old Alluvium: pebbles, coarse sand, medium to coarse sand, clay and silt, variably cemented.

  • Fort Canning Boulder Bed: a colluvial deposit of boulders in a soil matrix that is typically a hard silt or clay.

  • Jurong Formation: sandstones, siltstones, mudstones, conglomerate and limestone, subjected to a varying degree of metamorphism.

  • Bukit Timah Granite: granitic rocks including granodiorite, adamellite and granite, with associated residual soils.

What changed with BCA's 2021 geological map?

BCA replaced the 2009 geological unit names with a new stratigraphic framework, published in 2021 as a 1:50,000 scale geological map and a geological memoir. Circular APPBCA-2021-18 (1 October 2021) explains the history: the first Geology of Singapore was issued in 1976 by the former Public Works Department and revised in 2009 by DSTA. From 2012 to 2018 BCA carried out geological survey works in support of the Underground Master Plan, then worked with the British Geological Survey on a framework that follows International Commission on Stratigraphy guidelines.

Three BCA documents now make the new names part of everyday practice:

  • APPBCA-2022-02 (1 March 2022): SI data in the AGS(SG) electronic format based on the new framework is required for all SI works carried out from 1 October 2022, and the new unit names apply to borehole logs as well.

  • APPBCA-2025-16 (1 September 2025): SI reports must adopt the new stratigraphic code for stratum descriptions and include a coloured Singapore Geological Map (BCA, 2021) showing the site boundary and borehole locations. It applies to SI reports dated on or after 1 March 2026 and to new projects applying to URA for planning permission on or after that date.

  • BCA's 20 September 2023 reminder on Regulation 31 of the Building Control Regulations: the design Qualified Person must carry out a desk study, with reference to the Singapore Geological Map, before planning the investigation.

How do the old names map to the new names?

Annex A of circular APPBCA-2021-18 sets out the official comparison between the 2009 (DSTA) units and the 2021 (BCA) units. Some are direct one-to-one matches and others are only broadly equivalent:

  • Kallang Formation is now the Kallang Group. Its Marine Member is broadly equivalent to the Rochor Clay Formation and the Tanjong Rhu Clay Formation (which includes the Marina South Member). The Alluvial Member corresponds to the Jalan Besar Formation, the Transitional Member to the Kranji Formation, the Reef Member to the Semakau Formation and the Littoral Member broadly to the Tekong Formation.

  • Old Alluvium corresponds directly to the Bedok Formation.

  • Fort Canning Boulder Bed corresponds directly to the Fort Canning Formation.

  • Jurong Formation (Tengah, St John, Rimau, Pandan, Ayer Chawan, Jong and Queenstown facies) is broadly equivalent to several new units: the Jurong Group (Tuas, Pulau Ayer Chawan, Pandan and Boon Lay Formations), the Sentosa Group (Tanjong Rimau and Fort Siloso Formations), the Buona Vista Formation and the Kusu Formation.

  • Bukit Timah Granite is broadly equivalent to a set of plutons, most of them grouped as the Bukit Timah Centre: the Simpang Granite, Pulau Ubin Granite, Dairy Farm Granite-microgranite and Choa Chu Kang Granodiorite-tonalite Plutons.

  • Gombak Norite corresponds directly to the Gombak Gabbro-granite Pluton.

Because several mappings are many-to-one, an old borehole log cannot be converted by find-and-replace. The unit has to be re-identified from the description, the location on the 2021 map and, where needed, the cores.

What does Kallang Formation marine clay mean for design?

Marine clay of the Kallang Formation is the soft, compressible layer that governs settlement, negative skin friction and excavation support design wherever it is present. BCA's Guidelines for Electronic Transfer of Site Investigation Data (Edition 3.0) label the new units in the terms engineers already use: the Rochor Clay Formation is the upper marine clay, the Tanjong Rhu Clay Formation is the lower marine clay, and the Marina South Member is the desiccated stiff clay layer between them.

For design this means long-term consolidation settlement under new fill or load, downdrag on piles, and low undrained strength that controls the stability of excavations. The GeoSS guide to Eurocode 7 places a foundation for a building of more than 10 storeys on reclaimed land, or on soft soils with a combined thickness of more than 8 m, in Geotechnical Category 3, the highest category. We cover the mechanics in marine clay settlement and land reclamation in Singapore.

What is the Old Alluvium and why do engineers like it?

The Old Alluvium (now the Bedok Formation) is an alluvial deposit that has been variably cemented, often to the extent that it has the strength of a very weak or weak rock, according to LTA's Civil Design Criteria. That makes it a common founding stratum for piles.

Its upper zone is typically weathered, and LTA's guidance classifies it from Class A (unweathered) to Class E (residual). The SPT blow count is commonly used as an indicator: more than 50 blows per 300 mm for Classes A and B, 30 to 50 for Class C, 10 to 30 for Class D and below 10 for Class E. LTA cautions that SPT should not be used in isolation, because cementation, hardpan layers and uniform sand layers all affect the result. Unlike the granite or the Jurong rocks there is little evidence of joints, so weathering generally advances as a front from the surface.

What should engineers know about the Jurong Formation and limestone cavities?

The Jurong Formation is a variable sequence of sedimentary rocks with a wide range of strength, and parts of it contain limestone with cavities. LTA notes that much of the formation is thinly bedded. BCA describes the geology of western Singapore as complex and affected by numerous fold and thrust zones, so the rock type and rockhead level can change over short distances.

The joint BCA/IES/ACES/GeoSS circular APPBCA-2025-17 (1 September 2025) states that limestone occurs in four formations (Pandan, Tuas, Pulau Ayer Chawan and Boon Lay) and two members (Nanyang and Clementi) of the Jurong Group. The Pandan Formation is about 72% carbonate rock with limestone beds 5 to 50 m thick, and the Tuas Formation about 23% with beds 1 to 20 m thick. The circular records no documented case of these cavities appearing as surface sinkholes in Singapore, but piles can meet cavities or slump zones at depth. It sets risk categories by formation and building type and applies from 1 March 2026. See foundation design, pile types and site investigation for how this affects piling.

What about Bukit Timah Granite and its residual soil?

Weathered Bukit Timah Granite typically has a thick mantle of residual soil with only limited completely or highly weathered rock beneath it, so the change from soil to strong rock can be abrupt. LTA's criteria use six weathering grades, from Grade I (fresh) to Grade VI (residual soil), and call for careful and frequent sampling once the SPT value reaches 30 blows per 300 mm, so that the thin transition grades are not missed. BCA's SI report guideline also warns that boulders or corestones may affect test results.

For foundations the practical issues are identifying true rockhead rather than a boulder, and socketing piles into rock of the grade the design assumed. For excavations and slopes, residual soil behaviour is tied to rainfall and groundwater, covered in our article on slope stability and the risk-based slope design framework.

What are the Fort Canning Boulder Bed and reclaimed land?

The Fort Canning Boulder Bed (now the Fort Canning Formation) is a colluvial deposit of boulders in a hard silt or clay matrix, largely derived from Jurong Formation rocks. LTA notes it was previously known as S3 or bouldery clay. Boulders obstruct piles and walls and make borehole results hard to interpret, so the investigation and the wall or pile installation method need to anticipate them.

Reclaimed land and fill are man-made ground placed over the natural units, and the new load compresses any soft soil beneath. LTA's criteria require downdrag to be considered in man-made ground and any other material that is prone to consolidation. The design questions are how much settlement remains and whether the fill itself was improved.

What goes wrong when the geology is misread?

Most problems come from assuming the ground is simpler than it is. Common errors include:

  • Using superseded unit names, or leaving out the geological map extract, in SI reports dated on or after 1 March 2026.

  • Reading only the surface map. BCA points out that the bedrock map shows formations near the surface and that a limestone-rich unit such as the Pandan Formation may lie beneath a younger unit.

  • Classifying Old Alluvium weathering by SPT alone, against LTA's caution.

  • Too few boreholes near the boundary between two formations or near old watercourses, which BCA's 2023 reminder specifically asks designers to cover.

  • Treating a boulder or corestone as rockhead.

A sound soil investigation planned by the designer is the control for all of these.

FAQ

Is the Kallang Formation the same as marine clay?

No. Marine clay is one part of it. The Kallang Formation also includes beach sands, estuarine peats and organic clays, and fluvial sands and clays.

What is the Old Alluvium called now?

The Bedok Formation. BCA's 2021 framework treats this as a direct correlation with the Old Alluvium of the 2009 map.

Where is limestone found in Singapore?

BCA states that natural limestone formations occur in western Singapore within units of the Jurong Group, chiefly the Pandan and Tuas Formations.

Do I have to use the new geological names in my SI report?

Yes. New unit names have been required for SI works carried out from 1 October 2022, and the SI report guideline in force from 1 March 2026 makes the new stratigraphic code a minimum requirement.

Where can I check the geology of my site before drilling?

BCA's SI report guideline lists the Singapore Geological Maps and Memoir (BCA, 2021) and existing borehole data available to the public through SLA's INLIS portal as key resources for the desk study.

Is Bukit Timah Granite a single rock body?

Not in the new framework. It is mapped as several plutons, most of them grouped as the Bukit Timah Centre.

Sources

CVC Engineers advocates education and public awareness, and has a dedicated team to help resolve this properly. WhatsApp +65 9342 7551. Last reviewed: November 2026.

Recent Posts

See All

Comments


© 2024 CVC Engineers. All rights reserved.

bottom of page