Soil and Rock Mechanics Basics: Shear Strength Compressibility and the Parameters Engineers Use
Soil and rock mechanics is the study of how the ground carries load, deforms and lets water through. Almost every geotechnical design in Singapore reduces to a short list of parameters: a classification, a shear strength (drained or undrained), a stiffness or compressibility, a permeability and, in rock, a measure of rock mass quality such as RQD. This primer explains each in plain language, says which test produces it, and shows how BCA's site investigation report guideline (circular APPBCA-2025-16, in force for SI reports dated on or after 1 March 2026) expects it to be reported. It supports our complete guide to geotechnical engineering in Singapore.
What is soil mechanics and why does it matter for a building project?
Soil mechanics turns borehole samples and test numbers into predictions of bearing capacity, settlement, wall movement and slope stability. Unlike steel or concrete, the ground is not manufactured to a specification. Its properties have to be measured on each site, and Regulation 31 of the Building Control Regulations 2003 requires the Qualified Person for structural works to carry out proper and adequate site investigation where foundations, tunnels, excavations or related earthworks are proposed.
BCA's 20 September 2023 reminder to design QPs names the relevant standards as Eurocode 7 and the Geotechnical Society of Singapore (GeoSS) Guide on Ground Investigation and Geotechnical Characteristic Values to Eurocode 7, and requires SI works to be done by an inspection body accredited by the Singapore Accreditation Council (SAC).
How are soils classified in a Singapore borehole log?
Soils are classified by particle size into gravel, sand, silt and clay, then described by consistency or density, colour, secondary constituents and geological origin. Coarse soils (sand and gravel) get their strength from friction between grains and drain quickly. Fine soils (silt and clay) hold water, drain slowly and can be soft and compressible.
BCA's guideline APPBCA-2025-16 replaces the older Singapore material codes with Eurocode 7 compliant codes: Gr for gravel, Sa for sand, Si for silt, Cl for clay and Pt for peat, with prefixes for secondary constituents such as siSa for silty sand or saCl for sandy clay. Its field guide sheet for soil sets the order of description as consistency or density, colour, soil name, weathering grade, particle shape, structure, geological formation and site observations, with the geological name taken from Singapore Geology (BCA, 2021). The guideline lists moisture content, bulk density, Atterberg limits (liquid limit, plastic limit, plasticity index) and grain size analysis as the critical laboratory results for soil. Our article on Singapore geology for engineers explains the formation names.
What is effective stress?
Effective stress is the part of the total stress carried by the soil skeleton: total stress minus pore water pressure. It is the single most important idea in soil mechanics, because soil strength and compression respond to effective stress, not total stress.
Two practical consequences follow. First, raising the water pressure in the ground (after heavy rain, or from seepage into an excavation) lowers effective stress and so lowers strength, with no change in load. Second, lowering the groundwater table raises effective stress in the soil below, which compresses soft clay and causes settlement some distance from the pumping. This is why groundwater levels and piezometer readings sit alongside strength data in any design, and why instrumentation and monitoring tracks water as closely as movement.
What is the difference between drained and undrained shear strength?
Undrained shear strength (cu) is the strength of a saturated clay loaded faster than water can escape. Drained strength is the strength available once excess pore pressures have dissipated, expressed with the effective stress parameters c' (effective cohesion) and φ' (effective angle of shearing resistance).
Undrained (short-term, total stress) analysis usually governs soft clay immediately after loading or excavation.
Drained (long-term, effective stress) analysis governs sands at all times and clays in the long term.
Neither is automatically the safe choice, so Singapore practice checks both. LTA's Civil Design Criteria (Revision A2, September 2019) requires both total stress and effective stress analysis for deep foundation elements, with the more onerous governing, and BCA's Advisory Note 1/09 on earth retaining or stabilising structures lists the effects of onerous soil loading from both drained and undrained conditions among the design considerations. The GeoSS guide lists tan φ', c', cu, SPT N and CPT qc as the parameters for which characteristic values must be determined. How those become design values is covered in Eurocode 7 in Singapore.
What does the SPT N value tell you?
The Standard Penetration Test N value is the number of hammer blows needed to drive a sampler 300 mm into the soil at the bottom of a borehole. It is an index of density in sands and consistency in clays, and the most widely used number in Singapore borehole logs.
The field guide sheet in BCA's guideline APPBCA-2025-16 relates N to descriptive terms:
Coarse soils: very loose 0 to 4, loose 4 to 10, medium dense 10 to 30, dense 30 to 50, very dense above 50.
Fine soils: very soft 0 to 2, soft 2 to 4, firm 4 to 8, stiff 8 to 15, very stiff above 15.
The guide sheet states that it is for preliminary field logging and that descriptions should be cross-checked against laboratory and in-situ test results. Because the energy a hammer delivers varies between rigs, the guideline requires a calibration certificate for each SPT hammer used and the SPT energy ratio (Er) to be reported in the borehole log. N is not a strength. It is correlated to strength and stiffness, and those correlations depend on the soil type. See soil investigation in Singapore for how boreholes are planned.
What are compressibility and consolidation?
Compressibility is how much a soil shortens under added effective stress, and consolidation is the slow process by which a saturated clay compresses as water is squeezed out. Sands compress almost at once. Clays can take years, because their permeability is so low.
The laboratory test is the oedometer (one-dimensional consolidation) test, which gives the compression parameters, the coefficient of consolidation that controls the rate, and the preconsolidation pressure, the greatest effective stress the clay has carried in the past. The Guidelines on Local Practices for Pile Foundation Design and Construction (18 January 2022, listed on BCA's guidelines page) use this directly: the preconsolidation pressure is found from oedometer or constant rate of strain tests, or from cone penetration tests, and the over-consolidation ratio (OCR) is that pressure divided by the designed vertical effective stress. Where OCR is less than 1.0, the clay will keep consolidating and drag force on piles must be considered. The full picture is in marine clay settlement and land reclamation.
What is permeability and when does it govern?
Permeability is the ease with which water flows through soil or rock, and it governs dewatering, seepage into excavations and the time consolidation takes. Clean sands and fractured rock are far more permeable than intact clay, so the same excavation can be nearly dry in one stratum and need cut-off walls and pumping in another.
The GeoSS guide notes that the coefficient of permeability can be evaluated from field tests, from an oedometer test and from laboratory permeability tests on soil specimens. BCA's guideline lists the field permeability (packer) test among the tests that need equipment calibration certificates. Design implications are in groundwater control and dewatering for excavations.
How is rock quality described: strength, weathering and RQD?
Rock is described at two scales: the intact material (strength and weathering grade) and the rock mass (how broken it is by joints, measured by core recovery and RQD). Rock Quality Designation is the percentage of a core run recovered as sound pieces of core above a standard length. A high RQD means massive rock, and a low RQD means closely fractured rock that behaves far more weakly than a laboratory sample suggests.
BCA's guideline APPBCA-2025-16 requires:
Total core recovery (TCR), solid core recovery (SCR) and RQD for each core run, on the borehole log and on the core box labels.
Rock strength terms tied to unconfined compressive strength (UCS), running from extremely weak (0.6 to 1 MPa) through medium strong (25 to 50 MPa) to extremely strong (above 250 MPa).
Weathering Grades I (fresh) to VI (residual soil) from EN ISO 14689.
UCS and point load index as the critical laboratory results for rock, with UCS tests carried out on intact samples with no discontinuities.
Which test gives which parameter?
Each design parameter has a preferred field or laboratory source, summarised here from Annex B of the GeoSS guide and BCA's SI report guideline:
SPT: density index and effective angle of shearing resistance in coarse soils, with a disturbed sample for description.
Cone penetration test (CPT): effective angle of shearing resistance, drained modulus and oedometer modulus.
Field vane test: undrained shear strength of soft clay.
Pressuremeter test: stiffness, and resistance factors for spread foundations and piles.
Flat dilatometer test: oedometer modulus.
Plate loading test: undrained shear strength, modulus and coefficient of subgrade reaction.
Laboratory classification tests: moisture content, bulk density, Atterberg limits and grain size.
Triaxial tests: shear strength parameters and stiffness.
Oedometer tests: compressibility and consolidation parameters.
UCS and point load tests: intact rock strength.
How does BCA expect parameters to be reported?
From 1 March 2026, BCA's guideline APPBCA-2025-16 sets mandatory minimum contents for SI reports submitted for building works. The main ones are:
A standalone SI report in PDF plus the data in AGS(SG) format. The SI report is not to be renamed or merged into the QP's design report.
Certification by an appropriate Professional Engineer verifying the accuracy of the information.
Stratum descriptions using the new stratigraphic code and the Eurocode 7 compliant material codes.
An as-built borehole plan, a coloured Singapore Geological Map (BCA, 2021) extract and a table of coordinates in SVY21 and levels in Singapore Height Datum.
Field and laboratory results reported to the applicable EN or BS standards, with equipment calibration records, as substantiation for the parameters proposed. Laboratory test reports are to come from SAC-accredited laboratories.
SPT hammer calibration certificates and the energy ratio on each log.
The guideline applies to QPs and to SAC-accredited SI firms.
What goes wrong with soil parameters?
Parameter errors are usually errors of interpretation, not arithmetic. Typical ones are:
Treating SPT N as a direct strength without checking the correlation suits the soil.
Running only an undrained or only a drained check when the other governs.
Averaging results across different strata, or across both sides of a geological boundary.
Using intact rock strength where the fractured rock mass controls.
Too few tests to support a characteristic value. BCA's observational method framework (APPBCA-2019-12), for example, sets a minimum of 10 strength samples before characteristic and most probable parameters can be derived statistically.
Ignoring groundwater, the one variable that changes effective stress without any change in load.
FAQ
What is a good SPT N value for a foundation?
There is no single figure. N must be read with the soil type, the geological unit and the foundation type. BCA's field guide classes sand above N = 50 as very dense and clay above N = 15 as very stiff.
What is the difference between cu and c'?
cu is undrained shear strength, used in short-term total stress analysis of clay. c' is effective cohesion, used with φ' in long-term effective stress analysis.
Is RQD the same as rock strength?
No. RQD measures how fractured the rock mass is. Strength of the intact rock is measured separately by UCS or point load tests.
Who decides which tests are done?
The designer. BCA's guideline says Eurocode 7 makes designers responsible for planning the investigation and the necessary field and laboratory tests, and advises developers to engage their QPs early so that methods and tests are settled within the SI contract.
Can results from a neighbouring site be used?
They help the desk study, and the GeoSS guide allows previous investigation data to be considered, but each site needs its own investigation to the extent the design requires.
Does an SI report need a PE's signature?
Yes. Certification by an appropriate Professional Engineer is a minimum requirement under BCA's guideline.
Sources
BCA reminder to design QPs on site investigation and Regulation 31 (20 September 2023)
Guidelines on Local Practices for Pile Foundation Design and Construction (18 January 2022)
BCA Advisory Note 1/09 on Earth Retaining or Stabilising Structures (2 April 2009)
BCA framework on the observational method, circular APPBCA-2019-12
LTA Civil Design Criteria for Road and Rail Transit Systems, Revision A2 (September 2019)
Building Control Regulations 2003, Regulation 31 (Singapore Statutes Online)
For a review of the parameters behind a foundation or excavation design, see our foundation design review and PE geotechnical and tunnel endorsement services.
CVC Engineers advocates education and public awareness, and has a dedicated team to help resolve this properly. WhatsApp +65 9342 7551. Last reviewed: November 2026.


Comments