10 Common Misunderstandings About PE Endorsement in Singapore
A PE endorsement is a registered Professional Engineer's signed and stamped certification of specific drawings, calculations or works. It is not a government approval, it is not transferable to a changed design, and it does not move the owner's legal duties onto the engineer. Most problems with endorsements start from one of ten beliefs that sound reasonable and are wrong. Each is set out below as people usually say it, followed by the fact and its source.
For the full picture, start with our main guide to PE endorsement in Singapore.
1. "Any engineer can endorse"
Only a registered professional engineer with a practising certificate in force can endorse. The Professional Engineers Board (PEB) states that, under the Professional Engineers Act, a person who engages in professional engineering work in the prescribed branches in Singapore must be a registered professional engineer who has in force a practising certificate, or someone working under the direction or supervision of one.
An engineering degree, a job title of "engineer" or years of site experience do not meet this test. PEB's public directories list engineers with active practising certificates, and checking takes a few minutes: see how to check a Professional Engineer.
2. "A contractor's in-house PE stamp is enough"
A business may supply professional engineering services only if PEB has licensed it, and the party receiving the endorsement often expects the PE to be appointed by the owner. PEB states that a person who supplies or offers to supply professional engineering services must be a PE with a practising certificate practising as a sole proprietor, as a partner in a licensed partnership or in a partnership made up wholly of registered PEs, or a licensed corporation or limited liability partnership. A renovation or building contractor that employs someone with a stamp is not, by that fact alone, licensed to sell engineering services.
The appointment matters too. The sample certification in BCA's advisory to management corporations of 14 January 2014 begins with the PE declaring that they were appointed by the subsidiary proprietor or the MCST. HDB's guidelines speak of the PE engaged to supervise the demolition and require the approved plan and conditions to be given to that PE.
A contractor may recommend an engineer. Check that the engineer and the firm appear in PEB's directories.
3. "PE endorsement is a government approval"
A PE endorsement is a professional's certification, and a government approval is a separate decision by an authority. BCA's guide for condo owners puts the two side by side: structural elements cannot be altered without proper assessment by a Professional Engineer, and approval from the Commissioner of Building Control is also required.
Where the law requires approval, the PE acts as a Qualified Person, submits structural plans and applies for a permit. BCA states that only a Qualified Person who is a professional engineer in the civil or structural discipline can apply for structural plan approval. Until BCA approves the plans and grants the permit, the works are not authorised, however many stamps the drawings carry. Our article on PE endorsement vs QP submission separates the two, and when PE endorsement is required lists the cases.
4. "Non-load-bearing walls never need anything"
Demolishing a non-load bearing wall is exempt from BCA plan approval, but it is not exempt from HDB or MCST approval. The First Schedule of the Building Control Regulations 2003 classes the demolition, restoration or reinstatement of a non-load bearing wall, and the creation of an opening in one, as insignificant building works. That removes one requirement only.
In an HDB flat, HDB states that all demolition or alteration of walls can only be carried out after obtaining HDB's approval, and a permit is required even for hollow block, brick and drywall partitions.
In a condo, BCA's 2014 advisory asks the MCST to require renovation plans endorsed by a civil or structural PE, certifying that no structural works are involved, for any demolition other than floor tiles.
BCA's guidance on works not requiring approval reminds owners that they must still observe safety and obtain required approvals from other authorities, and observe MCST by-laws.
Someone also has to establish, from the approved structural plans and an inspection, that the wall is in fact non-load bearing. See insignificant building works and PE endorsement for wall hacking.
5. "One endorsement covers later changes"
An endorsement covers the design that was endorsed, and material changes need to go back to the engineer and, where plans were approved, to BCA. BCA's structural plan submission page states that if there are material changes to the approved plans during building, meaning changes that require a re-design of key structural elements, approval must be obtained before the change is carried out on site. Immaterial changes can proceed, but a record must be kept and incorporated in subsequent structural plans.
The same principle applies to an endorsement that never went to BCA. A stamped drawing for a platform carrying a stated load does not cover a heavier machine placed on it next year. If the scope moves, ask the engineer in writing whether the endorsement still stands.
6. "An endorsement is just a stamp, so it should take one day"
The stamp is the last step of a check that the certification wording itself describes. In BCA's sample certification for strata renovation, the PE states that they have personally checked the approved structural plan and inspected the structural condition of the building or unit. In BCA's standard certificate for additions and alterations, the PE states that they have inspected the existing building and investigated its overall structure, and that in their opinion the building and its foundation can resist the forces altered by the works.
Those statements cannot be made honestly without obtaining the approved plans, reading them, visiting the site and, where load is added or structure altered, doing calculations. Where BCA approval is needed, BCA's own service standard is 7 working days for structural plans without an Accredited Checker's certificate and 7 working days for the permit, counted from complete documents. What the signature commits the engineer to is covered in what a PE endorsement carries.
7. "The PE is responsible, so the owner is not"
Engaging a PE does not remove the owner's responsibility. The agencies say so in plain terms:
HDB: "You are responsible for the renovation in your flat", and the owner must ensure that the contractor's work is in line with HDB's guidelines. HDB's terms also require the owner to indemnify HDB against claims arising from the work, and an owner who breaches the renovation rules can be fined up to $5,000 on conviction.
BCA, on temporary buildings: it is the owner's responsibility to ensure the safety of the temporary building or structure and to demolish it when the permit expires.
BCA, on private homes: building owners found to have unauthorised additions or alterations will have committed an offence under the Building Control Act. The maximum penalty for unauthorised building works is a fine of $200,000, imprisonment of 2 years, or both.
The PE carries professional responsibility for what they certify. The owner remains the person who must obtain the approvals, appoint the right people and keep the works within what was approved.
8. "A PE from overseas can endorse"
Overseas registration does not by itself allow an engineer to endorse work in Singapore. The requirement stated by PEB is registration under Singapore's Professional Engineers Act with a practising certificate in force. For building works, BCA states that a Qualified Person must be registered as an architect with the Board of Architects or as a professional engineer with PEB, and must hold a valid practising certificate issued by that board.
PEB does keep a separate Directory of Registered Foreign Professional Engineers alongside its directory of PEs with practising certificates. If an engineer's standing in Singapore rests on foreign registration, ask which PEB directory they appear in and confirm with the agency receiving the document that it will accept their endorsement. An engineer who is not registered here may work under the direction or supervision of a registered PE with a practising certificate, but the endorsement that an agency relies on has to come from someone the Singapore system recognises.
9. "All PEs can endorse all works"
A PE may endorse only within the branch of engineering they are qualified to practise. PEB registers professional engineers in the civil, electrical, mechanical and chemical branches, and states that the practising certificate authorises a PE to engage in professional engineering work within the branch of engineering that he is qualified to practise.
The agencies then specify the branch for each task:
BCA: structural plan approval can be applied for only by a QP who is a PE in the civil or structural discipline.
HDB: demolition of non-load bearing RC elements must be supervised by a PE for civil or structural works.
BCA, temporary buildings: the owner must engage a civil or structural PE to design, supervise and inspect.
SCDF: minor additions and alterations may be lodged by a registered architect or a PE in the civil, structural, mechanical or electrical discipline.
PEB also registers specialist professional engineers, for example in geotechnical engineering, for which a civil PE with a valid practising certificate must meet further qualification and experience requirements.
A mechanical PE's stamp on a mezzanine drawing, or a civil PE's stamp on an electrical single-line diagram, is the wrong stamp. See PE stamp and PE chop: what each discipline stamp means.
10. "No approval is needed if the works are inside my unit"
Owning or leasing the unit does not make its structure yours to alter. In strata developments, BCA's Strata Management Guide 11 lists "any structural element of the building" as common property whether or not it is within a lot, and an owner cannot alter common property without the management corporation's approval. Under section 37(4) of the Building Maintenance and Strata Management Act, as BCA's Guide 14 explains, works affecting the appearance or structural integrity of the building need the management corporation's authorisation first.
In HDB flats, certain works can only be carried out with HDB's prior written approval, and work done without the permit is unauthorised and may have to be reinstated. In industrial premises, the landlord's consent is a separate layer: JTC, for example, requires its consent for development or renovation works on its land and buildings. The Building Control Act also applies to building works inside a unit, such as a mezzanine, unless a First Schedule exemption applies. See mezzanine floor approval and lessons from recent enforcement.
Who governs what?
Professional Engineers Board: who is a PE, in which branch, and which firms may supply professional engineering services, under the Professional Engineers Act.
BCA: plan approval, permits and Qualified Person duties under the Building Control Act, and guidance to management corporations under the Building Maintenance and Strata Management Act.
HDB: renovation permits for flats under the Housing and Development (Renovation Control) Rules.
MOM, SCDF, JTC and other bodies: their own requirements for PE involvement in scaffolds and lifting, fire safety works and landlord consent.
What goes wrong when these beliefs are acted on
A wall is removed on the strength of a contractor's assurance, steel bars appear, and the work has to stop while HDB or BCA is informed and a PE is called in.
An endorsement is obtained for one layout and a different one is built.
A buyer inherits unauthorised works and has to regularise them. See regularisation of unauthorised works.
FAQ
What is PE endorsement in construction?
It is a registered Professional Engineer's signed and stamped certification of specific drawings, calculations or works. See PE endorsement meaning.
Is PE endorsement the same as BCA approval?
No. The endorsement is the engineer's certification. BCA approval is granted by the Commissioner of Building Control on a submission by a Qualified Person.
Can any PE endorse wall hacking?
No. HDB and BCA both specify a PE in the civil or structural discipline.
Does a non-load bearing wall need PE endorsement?
It needs no BCA plan approval. HDB still requires a permit for any wall demolition, and BCA has advised MCSTs to require a PE-endorsed plan for demolition other than floor tiles.
What documents does a PE need from me?
The address, approved plans, drawings of the proposed works, photos and the requirement you have been given. See PE endorsement form and documents.
Sources
Professional Engineers Board: Licensing requirements for corporations and partnerships
BCA: Advisory on control of renovation works, 14 January 2014
BCA: Appendix D, standard certification by the Professional Engineer for additions and alterations
BCA Strata Management Guide 11: Management and maintenance of common property
Singapore Statutes Online: Building Control Regulations 2003, First Schedule
CVC Engineers advocates education and public awareness, and has a dedicated team to help resolve this properly. For a specific question, see our PE endorsement and professional engineer consultation services. WhatsApp +65 9342 7551. Last reviewed: November 2026.


Comments