Pre Purchase Building Inspection in Singapore: What an Engineer Checks
A pre-purchase building inspection is a structural due diligence check that a buyer commissions before committing to a property. In Singapore an engineer compares the building against its approved plans, looks for unauthorised works, assesses visible structural condition, checks floor loading where the buyer plans heavy use, and reviews the building's Periodic Structural Inspection (PSI) and Periodic Facade Inspection (PFI) status. It is a visual, non-destructive assessment that informs price and contract terms. It is not a valuation and it is not a guarantee that no hidden defect exists.
What does a pre-purchase structural assessment cover?
A pre-purchase assessment covers four things: what was approved, what was actually built, what condition it is in, and what statutory obligations the buyer will inherit. The engineer's working sequence is usually:
Document review: approved building and structural plans, the Temporary Occupation Permit or Certificate of Statutory Completion, past PSI and PFI reports, and any notices or orders the seller has received.
Site inspection: a walk-through of every accessible space, the roof, the external envelope and the surrounding ground, recording cracks, spalling concrete, corrosion, deflection, damp and signs of movement.
Comparison: checking the built layout against the approved plans to find additions, removals and changes of use.
Report: a written account of findings, their likely significance, what could not be inspected, and what further investigation or rectification is recommended.
Singapore's building regime explains why step 3 matters. Building works need BCA plan approval and a permit unless they are insignificant building works, and carrying out works without approval is an offence under the Building Control Act with a fine of up to $200,000, imprisonment of up to 2 years, or both. When a property changes hands, responsibility for dealing with what is on the site passes to the new owner.
What does the engineer check on different types of property?
The scope depends on the building type, because each has its own typical weak points and its own regulatory exposure.
Landed houses:
Extensions, roof terraces, attics, basements and car porch roofs added after the original approval.
Retaining walls and slopes, especially on sloping sites. See retaining walls and slopes for landed houses.
Signs of differential settlement: stepped or diagonal cracking, sloping floors, gaps at junctions with extensions.
Spalling concrete and roof leaks, covered in spalling concrete and ceiling leaks.
Landed houses used solely as residences are outside both the PSI and PFI regimes, so there is no earlier engineer's report to rely on.
Shophouses:
The party walls, which URA describes as the principal load-bearing walls, and any openings cut into them.
Timber main beams, secondary beams and floorboards: rot, termite damage, notching and overloading from a change of use.
Rear extensions, added mezzanines, roof decks and heavy equipment on timber floors.
Whether the building is conserved.
Industrial property:
Design floor loading against the buyer's intended machinery, racking and storage.
Mezzanines, platforms and racking installed without approval. See mezzanine floor approval in Singapore.
Slab condition at loading bays, forklift routes and machine bases.
Steel roof structure, purlins and cladding fixings.
Commercial and strata property:
PSI and PFI history, outstanding rectification, and for strata units the management corporation's records and sinking fund exposure to upcoming repairs.
Facade condition and exterior features such as cladding, canopies and signage supports.
Alterations to structural elements made during past fit-outs.
How does the engineer check for unauthorised works?
The engineer compares the building as it stands against the plans BCA approved, element by element. Anything on site that is not on the approved plans, and is not insignificant building works under the First Schedule of the Building Control Regulations 2003, is potentially unauthorised.
The approved plans come from BCA's Plan Purchase System. BCA charges a search fee of $45 per address and $65 per plan reference number, both inclusive of GST, and says it will contact the applicant within 10 working days on availability if the application is in order. Applicants must show eligibility with ownership documents, so a buyer normally needs the seller's written authorisation. Build this into the option period. Our guide on how to buy approved structural plans and building plans from BCA sets out the steps.
Items that turn up most often:
Mezzanine floors and storage platforms beyond the First Schedule limits.
Roofed-over yards, air wells and terraces.
Rear and side extensions.
Removed or cut walls, beams and slabs, including new staircase openings.
Additional storeys or attic conversions.
Where unauthorised works are found, the buyer's options are to ask the seller to regularise or remove them before completion, to negotiate the price to reflect the cost, or to walk away. Regularisation of unauthorised building works is a full submission in its own right, and some works cannot be regularised at all. Recent enforcement cases are discussed in unauthorised mezzanines and building works.
Why does floor loading matter to industrial buyers?
Floor loading matters because every suspended floor was designed for a stated imposed load, and exceeding it is a structural safety issue, not a paperwork issue. An industrial buyer should have the engineer confirm three things:
The design imposed load shown on the approved structural plans for each floor.
Whether the buyer's planned machines, racking, stock and vehicles fit within that load, including concentrated loads under machine feet and rack uprights.
Whether the slab shows distress from the current occupier's use.
If the plans cannot be found, capacity can only be established by investigation and calculation, which is slower and costlier than reading a drawing. See machine foundations and floor loading in Singapore factories.
What should a buyer check about PSI, PFI and BCA notices?
A buyer should establish when the building's next PSI and PFI fall due and whether any inspection notice or repair recommendation is outstanding, because those duties follow the building.
PSI: BCA requires a structural inspection every 5 years for non-residential buildings and every 10 years for residential buildings, by a structural engineer the owner appoints after BCA's notice. Detached, semi-detached, terraced and linked houses used solely as residences, and temporary buildings, are exempt.
PFI: buildings more than 13 metres high and 20 years or older must have a facade inspection every 7 years. The owner must appoint a Competent Person within 2 months of the notice; BCA's FAQ gives the penalty for failing to do so as a fine of up to $20,000.
Sale during a notice: BCA's PFI FAQ states that a building being sold still needs to be inspected. If the buyer agrees to comply with the notice and BCA is told, BCA will consider holding the buyer accountable. An owner served with a notice remains under a duty to carry out the remedial works the Competent Person recommends, even if the owner intends to sell.
Ask the seller, through your conveyancing lawyer, for the last PSI and PFI reports, any BCA notices or orders, and evidence that recommended repairs were completed. The differences between the two regimes are set out in PSI vs PFI in Singapore, and all the mandatory regimes are listed in our building inspection hub.
What is different about conserved buildings?
A conserved building can only be altered with URA's Conservation Permission, which limits what a buyer can do with it and how defects may be repaired. URA states that conservation status has been given to over 7,000 buildings in almost 100 conservation areas since 1989, and a June 2026 URA circular counts over 6,500 conserved shophouses and terraces.
URA sorts works into three categories:
Category 1: works affecting key elements with significant impact, such as structural strengthening or a new rear extension. Submission by a Qualified Person who is a registered architect.
Category 2: works affecting key elements to a lesser extent, such as replacing roof tiles or adding an internal staircase. A registered architect or a professional engineer may act as Qualified Person.
Category 3: minimal, localised works or repair and maintenance, such as one-for-one localised replacement of timber floor boards and joists. No Qualified Person is needed, but Conservation Permission must still be issued before work starts.
For a buyer this means the engineer's report should separate defects that can be repaired like-for-like from proposals, such as replacing a timber floor with concrete, that URA's guidelines restrict. Buildings built before 1 January 1991 also need an asbestos survey before any alteration, addition, repair or demolition work, under MOM's rules.
What are the limits of a visual inspection?
A visual inspection reports only what can be seen and reached on the day. It cannot confirm the condition of anything concealed, and a careful report says so explicitly. Typical limits:
Foundations and buried structure are not visible. Their adequacy is inferred from the plans and from the absence of movement.
Reinforcement inside concrete, and its corrosion state, cannot be seen without testing.
Elements behind false ceilings, wall linings, built-in furniture and stored goods are not inspected unless opened up.
Concrete strength, timber decay inside a section and steel thickness loss need testing to quantify.
A single visit cannot show whether a crack is still moving. That takes structural monitoring over time.
Where the visual findings justify it, the engineer will recommend targeted tests such as cover meter scans, carbonation depth tests, coring or load assessment before the buyer commits.
What does the report give the buyer, and what is it not?
The report gives the buyer a technical basis for a decision and a list of costs and risks to price in. Used well, it supports:
Negotiating the price against the engineer's list of repairs and regularisation works.
Conditions in the contract, such as the seller removing unauthorised works or completing outstanding PSI or PFI repairs before completion.
A decision to commission further testing before exercising the option.
A maintenance and capital works plan for the first years of ownership.
What it is not:
Not a valuation. An engineer does not opine on market value; that is a valuer's role.
Not a guarantee or warranty against latent defects.
Not a statutory PSI or PFI report, which have their own prescribed scope and are submitted to BCA.
Not an approval. A favourable report does not regularise unauthorised works.
Not a legal title or planning search. Approved use, lease terms and encumbrances are checked by the buyer's lawyer.
What goes wrong when buyers skip or rush the inspection?
The usual failure is discovering after completion that part of the building was never approved or cannot carry the intended use. Common mistakes:
Relying on the seller's or agent's statement that a mezzanine or extension is "approved" without seeing the approved plans.
Applying for plans too late in the option period.
Inspecting only the unit and ignoring the common property, facade and roof in a strata development.
Assuming an industrial floor can take any racking because the previous occupier had racking.
Treating a clean visual report as proof of foundation or reinforcement condition.
Budgeting for renovation in a conserved shophouse without checking what URA will permit.
FAQ
Is a pre-purchase inspection mandatory in Singapore?
No. There is no legal requirement for a buyer to commission one. It is voluntary due diligence, separate from the mandatory PSI and PFI regimes that apply to owners.
Who should carry out a pre-purchase structural inspection?
A Professional Engineer in the civil or structural discipline is the appropriate person to assess structure, floor loading and unauthorised works. You can verify registration using our guide on how to check a professional engineer in Singapore.
Can I get the approved plans before I own the property?
Only with the owner's authorisation. BCA's Plan Purchase System requires eligibility and ownership documents, so ask the seller to sign the authorisation early.
Does the inspection include the foundations?
Only indirectly. The engineer reviews the foundation drawings where available and looks for signs of settlement or movement. Foundations are not exposed in a visual inspection.
What if the inspection finds unauthorised works?
You can ask the seller to regularise or remove them, renegotiate, or withdraw if your contract allows. If you buy with them in place, dealing with them becomes your responsibility as owner.
Is a pre-purchase inspection the same as a new home defects inspection?
No. A defects inspection of a newly completed home checks workmanship and finishes against the developer's obligations during the defects liability period. See new home defects inspection in Singapore.
Does a recent PSI report replace a pre-purchase inspection?
It helps, but it does not replace one. A PSI assesses structural condition for BCA's purposes; it is not written around a buyer's intended use and does not audit unauthorised works for a purchaser.
Sources
CVC Engineers advocates education and public awareness, and has a dedicated team to help resolve this properly, including pre-purchase structural assessment and regularisation of unauthorised works. WhatsApp +65 9342 7551. Last reviewed: November 2026.


Comments